Mobil SHC Gear 1000 (55 Gal. Drum)
Formulated from high-quality synthetic base fluids with exceptional oxidation and thermal properties, Mobil SHC Gear Series lubricants perform extremely well in plastic extruder gearboxes and modern, highly loaded gearboxes used in the paper, steel, oil, textile, lumber and cement industries, where gear protection and optimum oil life are needed. Mobil SHC Gear Series is a line of premium performance synthetic industrial gear oils that provide superior protection for bearings and gears, even under extreme conditions. Mobil SHC Gear 1000 has a viscosity index of 192, with ISO viscosity grade 1000, which equates to reduced viscosity change regardless of temperature variation, increasing your equipment’s ability to operate smoothly at both extreme high and low temperatures. Mobil SHC Gear oils also defend gearboxes against oil leakage, rust and corrosion. Extend oil life and drain intervals while preventing wear, scuffing and micropitting fatigue of your equipment's gears and bearings by using Mobil SHC Gear 1000.
Mobil SHC Gear Series lubricants are part of the Mobil SHC line of products that are recognized and appreciated around the world for innovation and outstanding performance. These synthetic products, pioneered by our research scientists, symbolize the continuing commitment to using advanced technology to provide lubricants with excellent balanced performance. A key factor in the development of Mobil SHC Gear Series was the close contacts between our scientists and application specialists with key OEMs to ensure that our product offering would provide exceptional performance with rapidly evolving industrial gear designs and operation. Not least among the benefits shown in work with OEMs is the ability to resist micropitting wear which can occur with some highly loaded, case-hardened gearing applications. This cooperative work also demonstrated the all-round balanced performance benefits for the new Mobil SHC Gear technology, including a wide temperature range of application.
To address the issue of micropitting wear, our product formulation scientists designed a proprietary combination of additives which would resist traditional gear wear mechanisms as well as protecting against micropitting. Mobil SHC Gear products provide exceptional oil life and deposit control and resistance to thermal/oxidative and chemical degradation, as well as the balance of the performance features. The patent-pending combination of synthetic base oils also provides exceptional low temperature fluidity characteristics unmatched by conventional mineral oil gear lubricants and is a key benefit for remote, low ambient temperature applications. The Mobil SHC Gear Series lubricants offer the following potential benefits:
| Features | Advantages and Potential Benefits |
| Superb protection from micropitting fatigue wear as well as high resistance to traditional scuffing wear | Helps extend gear and bearing life in enclosed gear drives operating under extreme conditions of load, speed and temperature Helps reduce unplanned downtime; less maintenance - especially critical for difficult to access gearboxes. |
| Excellent resistance to degradation at high temperatures | Helps extend oil life and drain intervals and reduce oil consumption, which can lower maintenance costs |
| Low traction | Helps reduce energy consumption and lower operating temperatures |
| High viscosity index equating to reduced viscosity change with temperature | Ability to operate at both high and low temperatures: especially critical in remote applications with no oil cooling or heating |
| Excellent resistance to rust and corrosion and very good demulsibility | Helps to ensure smooth, trouble-free operation at high temperatures or in applications subject to water contamination Excellent compatibility with a variety of soft metals |
| Excellent shear stability | Helps extend gear and bearing life |
| Resistence to filter plugging, even in the presence of water | Fewer filter changes; which can help reduce maintenance costs |
| Excellent seal compatibility | Less contamination and lower potential for oil leakage |
| Excellent compatibility with common gearbox materials and with mineral-based gear oils | Easy changeover from many mineral products |
Application Considerations: While the Mobil SHC Gear Series are compatible with mineral oil based products, admixture may detract from their performance. Consequently it is recommended that before changing a system to one of the Mobil SHC Gear Series, it should be thoroughly cleaned out and flushed to achieve the maximum performance benefits.
Mobil SHC Gear Series exceptional performance, synthetic industrial gear oils are designed to provide optimum equipment protection and oil life even under extreme conditions. They are especially formulated to resist micropitting of modern, case hardened gearing and can operate in both high and low temperature environments. Typical applications include:
- Modern, highly loaded gearboxes used in the paper, steel, oil, textile, lumber and cement industries where gear protection and optimum oil life are required.
- Plastic extruder gearboxes
Mobil SHC Gear Series ISO VG 150, 220, 320, 460 and 680 are approved under General Electric’s (GE) gear oil specification D50E35 for use in off-highway vehicle motorized wheel gearbox applications.
| Mobil SHC Gear meets or exceeds the following industry specifications | 150 | 220 | 320 | 460 | 680 | 1000 |
| Meets AGMA 9005-E02 | X | X | X | X | X | |
| Meets DIN 51517 Part 3 (CLP) | X | X | X | X | X | X |
| Meets ISO 12925-1 Type CKD | X | X | X | X | X | |
| Meets ISO 12925-1 Type CKT | X | X |
| Mobil SHC Gear has the following builder approvals | 150 | 220 | 320 | 460 | 680 | 1000 |
| SIEMENS AG Flender gear units, T 7300, Table A-c, Flender Code No. | A36 | A35 | A34 | A33 | A32 | A31 |
| SEW Eurodrive SEW IG CLP HC |
150 | 220 | 320 | 460 | 680 | 1000 |
| GE Motorized Wheel | D50E35 | D50E35 | D50E35 | D50E35 | D50E35 | D50E35 |
| Mobil SHC Gear Series | 150 | 220 | 320 | 460 | 680 | 1000 |
| ISO Viscosity Grade | 150 | 220 | 320 | 460 | 680 | 1000 |
| Viscosity, ASTM D 445 | ||||||
| cSt @ 40ºC | 150 | 220 | 320 | 460 | 680 | 1000 |
| cSt @ 100ºC | 22.2 | 30.4 | 40.6 | 54.1 | 75.5 | 99.4 |
| Viscosity Index, ASTM D 2270 | 176 | 180 | 181 | 184 | 192 | 192 |
| Pour Point, ºC, ASTM D 97 | -45 | -39 | -33 | -27 | -27 | -24 |
| Flash Point, ºC, ASTM D 92 | 233 | 233 | 233 | 234 | 234 | 234 |
| Brookfield @ 0ºF (-18ºC), cP, ASTM D 2983 | 41000 | 96000 | ||||
| Brookfield @ -20ºF (-28ºC), cP, ASTM D 2983 | 18200 | 35000 | 57000 | 107000 | 156000 | 500000 |
| Density 60ºF (15,6ºC), g/ml | 0.86 | 0.86 | 0.86 | 0.86 | 0.86 | 0.87 |
| Total Acid Number, mg KOH/g, ASTM D 664 | 0.9 | 0.9 | 0.9 | 0.9 | 0.9 | 0.9 |
| 4 Ball EP Test, kgf, ASTM D 2783 | ||||||
| Weld Load | 200 | 200 | 200 | 200 | 200 | 200 |
| Load Wear Index | 51 | 51 | 51 | 51 | 51 | 51 |
| FZG Micropitting, FVA Proc No. 54, 90°C | ||||||
| Fail Stage | 10 | 10 | 10 | 10 | 10 | 10 |
| GFT-Class | High | High | High | High | High | High |
| FZG Scuffing, ISO 14635-1 (mod) A/8.3/90, Fail Stage | 13 | 14 | 14 | 14 | 14 | 14 |
| FZG Scuffing, ISO 14635-1 (mod) A/16.6/90, Fail Stage | Not tested | >14 | >14 | >14 | >14 | >14 |
| Copper Corrosion, 3H @ 121°C, ASTM D 130 | 1B | 1B | 1B | 1B | 1B | 1B |
| Rust protection, ASTM D665, Sea Water | Pass | Pass | Pass | Pass | Pass | Pass |
| Demulsibility of EP Oils, Free Water, ml, ASTM D 2711 | 88 | 87 | 85 | 84 | 87 | |
| Water Separability, ASTM D 1401,Time to 40/37/3 at 82ºC, minutes | 10 | 10 | 10 | 15 | 25 | 40 |
| Foaming Characteristics, ASTM D 892,Seq. II, Tendency/Stability, ml/ml | 0/0 | 0/0 | 0/0 | 20/0 | 0/0 | 0/0 |
